- SubmeteredOn track
- AllocatedApproved
- Fixed chargeLive
- Commercial recoveriesSynced
Rioo Maintenance · Utilities & Assets
Utility & Asset Management Software for Property
Know every asset. Recover every utility dollar.
An equipment registry with warranties and service history, lifecycle planning, utility usage and cost tracking, itemized tenant billing and alerts for unusual consumption.
| Asset | Location | Last service | Status |
|---|---|---|---|
| Boiler #1 | Plant room | Last month | OK |
| Chiller #2 | Roof | Last quarter | Service due |
| Lift A | Tower | This month | OK |
Two quiet margin levers
Assets and utilities rarely make headlines, but they move margins. An asset replaced too early wastes capital. One replaced too late causes downtime and emergency spend. Utilities consumed but not recovered, or recovered but not explained, erode income and trust. RIOO puts both on the record, next to the properties and tenants they affect.
What is utility and asset management in property management?
Utility and asset management covers two linked jobs: tracking the physical assets in a property, such as boilers, lifts and roofs, across their life, and measuring, paying and recovering the cost of utilities such as water, gas and electricity. In RIOO both run on NetSuite, so asset costs, utility bills and tenant recoveries share the same ledger.
Together they are often the largest controllable costs in a building after payroll.
How it works
How does utilities & assets work in RIOO?
Utilities & assets in RIOO runs inside Oracle NetSuite. The properties, units, leases, tenants and vendors it uses are native NetSuite records, so each step updates the same data finance reports on. There is no separate system to sync, and every action keeps an audit trail. The steps below show how the work flows.
- 01
Register
assets with specs, warranties and documents.
- 02
Link
maintenance so every work order adds to the asset's history.
- 03
Track
utility usage and cost by property and unit.
- 04
Bill
tenants for their share with itemized statements.
- 05
Plan
replacements from lifecycle and cost data.
How it works
How does the asset lifecycle run in RIOO?
The asset lifecycle in RIOO runs from acquisition to disposal, with every service, repair and inspection recorded against the asset. This history is what lets managers plan replacements before failures and gives finance the data to set realistic capital budgets for each property.
- 01
Register
Add the asset with location, model, cost and warranty.
- 02
Schedule
Set preventive maintenance and inspection intervals.
- 03
Maintain
Log every work order and its cost against the asset.
- 04
Review
Compare repair spend with age and expected life.
- 05
Replace or dispose
Raise a capital project and retire the old asset.
In detail
How are utility costs recovered from residents and tenants?
Utility costs are recovered either by submetering each unit and billing actual usage, or by allocating the building bill using a formula such as floor area or occupants. RIOO supports both, posting recharges to each resident or tenant ledger and keeping them linked to the original utility bill for audit and dispute handling.
Submetered
Bills follow each unit's metered usage.
Allocated
Building bills are split by area, units or occupants.
Fixed charge
A flat utility fee is included in rent or billed separately.
Commercial recoveries
Utilities flow into CAM or service charge budgets.
In detail
How should you start an asset register?
Start an asset register with the assets that carry the most cost or risk, then add smaller items over time. A focused first register is quicker to build, easier to keep accurate and gives maintenance and finance useful data within the first few months instead of after a long data collection project.
Begin with compliance assets
Fire, gas, lifts and water safety.
Add high-cost plant
Boilers, chillers, roofs and generators.
Capture warranties
Dates and terms from purchase records.
Tag locations
Link each asset to its property, building and unit.
Add appliances later
Group them by type if there are many.
In detail
Asset capabilities
Equipment registry
for every tracked asset by property, building, unit or room.
Warranties
tracked with expiry alerts.
Service history
from every work order, attached to the asset.
Lifecycle planning
from acquisition through maintenance to replacement.
Repair-or-replace decisions
based on cost and performance history.
Depreciation
through NetSuite Fixed Asset Management, where your account uses it.
Documents
such as manuals, certificates and contracts, stored on the asset.
In detail
Utility capabilities
Consumption tracking
by property and unit.
Cost analysis
and trend comparison over time.
Itemized tenant billing
with clear usage records shown in the portal.
Unusual-consumption alerts
to catch leaks and faults early.
Utility billing integration
with National Utility Billing System.
Sustainability reporting
on usage across the portfolio.
Recovery models that match your properties
Different properties recover utilities differently: included in rent, flat fees, ratio billing (RUBS) or submetering. In manufactured housing communities, RIOO can reconcile resident billings against the master-meter invoice and report the recovery rate by community and month, with rules configured per state.
Asset data that pays off
Recording make, model, install date, warranty and service history for major equipment pays off in three ways. Technicians arrive prepared, warranty repairs are claimed rather than paid for, and replacement planning is based on evidence.
Compare
Which assets should be tracked individually?
Track an asset individually when it is expensive to replace, needs regular servicing or carries compliance obligations. Smaller items can be grouped. The table shows common asset types, why they are tracked and the records RIOO keeps for each, which helps decide what goes into the asset register at setup.
| Asset type | Why track it | Records kept |
|---|---|---|
| HVAC and boilers | Servicing, efficiency, replacement cost | Service history, warranty |
| Lifts and escalators | Safety inspections | Certificates, contracts |
| Roofs and façades | Large capital cost | Condition surveys |
| Fire and life safety | Legal compliance | Test logs, certificates |
| Appliances in units | Frequent repairs | Model, serial, warranty |
Why does NetSuite matter for assets and utilities?
NetSuite matters because asset and utility costs are financial as well as operational. In RIOO, a boiler repair is a work order and an expense on the same record, an asset purchase can feed NetSuite Fixed Asset Management for depreciation, and a utility recharge is both a cost recovery and a tenant receivable, with no transfer between systems.
Compare
Utility billing methods compared
RIOO supports utility charges on tenant accounts, with integration partners for meter reading and billing.
| Method | How it works | Best for |
|---|---|---|
| Direct metering | Each unit has its own utility account | Newer buildings with individual meters |
| Submetering | Building meter plus unit-level submeters, billed by usage | Multifamily and manufactured housing |
| RUBS | Costs allocated by a formula, such as occupants or square footage | Properties without submeters |
| Flat fee | A fixed utility charge per unit | Simple setups, or where included in rent |
Who is RIOO utilities and assets NOT for?
This module is not a building management system that controls equipment or reads sensors in real time, and it is not an energy trading platform. It records assets, maintenance, consumption and costs for property and finance teams. Sensor or meter data from specialist systems can be brought in through integrations.
What changes
What changes when utilities & assets runs on NetSuite?
When utilities & assets runs on NetSuite through RIOO, operational work and accounting stop being two separate jobs. Transactions post to the general ledger as they happen, reports use the same records as daily work, and controls come from NetSuite roles and approvals. The changes below are the ones teams usually notice first.
- Longer asset lifeand fewer surprise failures.
- Defensible capital plansbuilt on real history.
- Higher utility recoverywith fewer billing disputes.
- Earlier leak and fault detection
Talk to a specialist
See utilities & assets on your own portfolio.
An equipment registry with warranties and service history, lifecycle planning, utility usage and cost tracking, itemized tenant billing and alerts for unusual consumption.
What does the module cover?
On the asset side, the module covers the asset register, lifecycle tracking, depreciation, warranties and vendor coordination. On the utility side, it covers consumption, cost analysis, tenant billing, compliance and sustainability reporting. Both sides record costs in NetSuite against the right property, unit and asset for reporting.
How does RIOO help decide whether to repair or replace?
RIOO keeps the service history, repair costs and performance data for each asset, so managers can compare the cost of another repair with the cost of replacement. Age, expected life and warranty status sit on the same record, which turns a judgement call into a decision backed by data.
Do tenants see their utility usage?
Yes. Itemised utility bills and usage records are available to tenants, typically through the tenant portal, so they can see what they used and what they are being charged for each period. Clear usage data reduces billing disputes and helps residents understand and manage their own consumption.
Does RIOO calculate depreciation?
Depreciation is calculated through NetSuite Fixed Asset Management, where that module is part of your NetSuite account. RIOO asset records link to the fixed asset register, so depreciation schedules, disposals and book values stay consistent with the maintenance and cost history recorded for each asset.
Can utility consumption be compared across properties?
Yes. Consumption and cost can be reported per property, per unit and per square foot or square metre, so similar buildings can be compared fairly. Outliers often point to leaks, faulty equipment or billing errors, and the same data supports sustainability reporting to owners, lenders and investors.
Are warranties tracked so repairs are not paid twice?
Yes. Warranty dates and terms are stored on each asset, and technicians can see them before a repair is ordered. If an asset is still under warranty, the job can be routed to the manufacturer or installer instead of a paid vendor, which avoids paying for work that should be covered.
Can utility bills be entered automatically?
Utility bills can be captured as vendor bills and coded to properties and meters, reducing manual entry each month. Where a utility provider or billing partner supplies data electronically, it can be imported, which speeds up recharges and makes consumption reports available sooner.
Related
Related to utilities & assets




Put every asset and every utility dollar on the record.













